Ardob - Quote Request

Customer Information:

*Date: (DD-MM-YYYY)

Postal Code:

Fax:

Roll Specifications:

Max. Roll Width (in.):

Max Web Tension (PLI):

Min. Emergency Stopping Time (seconds):

Web Thickness Weight (lbs.):

Web Material:

Board Paper Film Foil Other

If other, specify:

Core Specifications:

Roll Stand Specifications:

Standard Flange Mounting:
flange specifications

Quick Disconnect Mounting:
NOTE: Can provide an ADAPTER PLATE to convert your flange type arbor to accommodate Single-Center-Bolt /Dowel Pin Type "Quick Disconnect" multiple size core chucks for QUICK-CHANGEOVER.

Stub Arbor Mounting:

NOTE: Stub-Arbor Mount chucks require a CENTER TAPPED HOLE, minimum 5/8" (16mm) diameter to ensure structurally adequate and safe stub-arbor mounting. The Arbor must be in good condition, with uniform diameter. This enables a close fit of the chuck onto the arbor; typically .002" (.05mm) diametral clearance to .0012" (.03mm) diametral interference. The key requires a close clearance fit. If the arbor has a shoulder, the chuck should be bored deep enough to permit clamping against the shoulder. THIS MOUNTING CONFIGURATION IS NOT RECOMMENDED IF FREQUENT CHUCK REMOVAL, TO CHANGE OVER SIZE, IS REQUIRED. An adapter plate can be made, as mentioned above, to convert the roll-stand to either flange mount or quick disconnect.

Customer Information:
*Company Name:
*Date: (DD-MM-YYYY)
Individual Contact:
Title:
Address Line 1:
Address Line 2:
State/Province:
Country:
Postal Code:
*Telephone:
Fax:
*Email Address:
Roll Specifications:
Max. Roll Weight (lbs):		Max. Roll Diameter (in):
Max. Roll Width (in.):		Max Web Tension (PLI):
Max. Web Speed (feet/min):		Web Material:
Min. Emergency Stopping Time (seconds):		Web Thickness Weight (lbs.):
Acceleration Time:		Deceleration Time:
Web Material:	Board Paper Film Foil Other	If other, specify:
Core Specifications:
Core Material:	Board Steel Plastic Aluminum Composite	Other:
Core Inside Diameter (in.):		Core I. D. Tolerance: ±
Current Core Reuse:		Number of Times (if applicable):
Roll Stand Specifications:
Roll Stand Manufacturer:		Model Number:
Approximate Age:		Maximum Distance between Roll-Stand Spindle and Mounting Flange:
Type of wind:	Unwind Rewind
Web Tension:		Single Brake or Dual Brake?:	Single Dual
Standard Flange Mounting:
"A" Thread Size Thru (in.) =		"B" Places Equally Spaced (in.) =
"C" Diameter Bolt Circle: (in.) =		"D" Arbor Pilot Diameter (in.) =
"E" Pilot Depth Female (in.) =		"F" Pilot Width Male (in.) =
"G" Spindle Flange O.D. (in.) =		"H" Spindle Flange Width (in.) =
Quick Disconnect Mounting: NOTE: Can provide an ADAPTER PLATE to convert your flange type arbor to accommodate Single-Center-Bolt /Dowel Pin Type "Quick Disconnect" multiple size core chucks for QUICK-CHANGEOVER.
Stub Arbor Mounting:
"I" Arbor Length (in.) =		"J" Arbor Diameter (in.) =
"K" Key Length(in.) =		"L" Key Width (in.) =
"M" Key Depth (in.) =		"N" Center Thread Size (in.) =
"O" Center Thread Depth (in.) =
NOTE: Stub-Arbor Mount chucks require a CENTER TAPPED HOLE, minimum 5/8" (16mm) diameter to ensure structurally adequate and safe stub-arbor mounting. The Arbor must be in good condition, with uniform diameter. This enables a close fit of the chuck onto the arbor; typically .002" (.05mm) diametral clearance to .0012" (.03mm) diametral interference. The key requires a close clearance fit. If the arbor has a shoulder, the chuck should be bored deep enough to permit clamping against the shoulder. THIS MOUNTING CONFIGURATION IS NOT RECOMMENDED IF FREQUENT CHUCK REMOVAL, TO CHANGE OVER SIZE, IS REQUIRED. An adapter plate can be made, as mentioned above, to convert the roll-stand to either flange mount or quick disconnect.
Comments:
If you would like to attach an application photo or an existing chuck drawing, please attach here: